Maintenance Level 1 (ML1) AMTP Evaluation Practice Test

These questions are part of the practice quiz. Start practicing

• For a target torque TA of 50 in-lbs with the same 8-inch wrench and 2-inch reverse-extension adapter, what should the torque wrench setting be?
• For a 7/32 inch flight control cable, what load test value would be used?
• Feder Specification WW-T-700/1 may be used in which application?
• What is the maximum allowable dent percentage for aluminum tubing unless it is on a short bend radius?
• If a component is received and is not identifiable because the data plate is missing and the established SN cannot be confirmed, what is the appropriate action?
• A component with a Time Between Overhaul (TBO) of 350 hours may be removed at how many hours?
• ARMS stands for which phrase?
• DA Form 2408-17 is used to document which type of record?
• What condition code is attached to condemned unserviceable components?
• Indiscriminate mixing of MIL-PRF-23699 and MIL-PRF-7808 may result in pressure differences from the published values for either oil.
• If you set TW to 35 in-lbs with L = 8 inches and E = 2 inches reverse extension, what is the actual torque TA?
• If a maintainer fails an evaluation, what happens?
• Where can you reference the use of Aircraft Forms and Records?
• AMAM stands for what?
• Which WP in TM 1-1500-204-23 covers HYD quick-disconnect couplings?
• According to TM 1-500-203-23, a bolt and screw with the marking L43 (MS030027) is made of what material?
• You are torquing a nut to 100 in-lbs. Using a 2-inch dog bone to extend the lever length on an 8-inch torque wrench, what should the wrench indicate to achieve proper torque?
• According to TC 3-04.71, what formal training is required for ML4 and Technical Inspectors?
• Who can perform MOC (Maintenance Operation Check)?
• The permitted removal window for a component with a 350 hour Time Between Overhaul is within which range?
• Suspended Tag Materiel is associated with which form number?
• Shaping the metal materials and parts used in aircraft construction, either with hand or power tools, is called?
• TM 1-1500-344-23 series is which topic?
• With an 8-inch wrench and a 2-inch reverse-extension adapter, what is the effective lever arm length from handle to fastener?
• What is the proper PPE required for performing lockwire or cotter pins?
• What is the EM number of the January 15, 2025 TM 1-1500-204-23?
• In flight operation status markings, what does the ⊗ symbol indicate compared to the X symbol?
• What is the purpose of DA Form 2408-13-1?
• What ARMY websites give information on current publications and forms?
• What is used to progress a maintainer's level of responsibility?
• The purpose of the TECHNICAL MANUAL AERONAUTICAL EQUIPMENT MAINTENANCE MANAGEMENT PROCEDURES
• What is the recommended torque value for a thin plain and castellated steel hex nut used with a bolt in the shear loading average range of a size and thread pitch of 3/8-24?
• An ML2 is a
• ARMS surveys are associated with which domain?
• Which form and supply condition code should be attached to an unserviceable condemned component that has no value and cannot be reclaimed?
• Which form is used for the Aircraft Inspection and Maintenance Record?
• What is the multiplying factor by which actual torque TA differs from the wrench reading TW for L = 8 inches and E = 2 inches reverse extension?
• When are dual brakes utilized?
• ML stands for what in this context?
• Maintenance action code L stands for which action?
• The dogbone adapter length used in the scenario is how many inches?
• Within a safety message (ASAM, AMAM, SOF), paragraph 11 is categorized as TECHNICAL PROCEDURES/INSTRUCTIONS.
• If you need to apply 35 in-lbs of torque and the setup uses an 8-inch length with an extension of -2 inches, what torque setting is required?
• Which of the following statements describes qualities of hydraulic fluid?
• DA Form 2408-20 records which type of data?
• Which form is used as the Oil Analysis Log?
• The statement 'There is no easy way to look at and tell the difference between the two types of oils' is true.
• GEN-24-AMAM-01 has three addendums.
• What does a horizontal dash indicate in condition status codes?
• HYD quick-disconnect couplings are documented under which WP in TM 1-1500-204-23?
• For TA = 60 in-lbs with L = 8 inches and E = 2 inches reverse extension, what TW should be set?
• Which method is used to progress each maintainer's level of responsibility?
• ML is based upon what concept?
• When and who can authorize a one-time evacuation flight?
• What are the two maintenance levels described in the material?
• Which document is replaced by GEN-24-AMAM-01?
• What WP in TM 1-1500-204-23 covers Desert Maintenance?
• Which of the following is a valid source for Army current publications and forms?
• What is entered into block 6e on the DA Form 2408-16?
• What does the term Root refer to when dealing with Main Rotor Blades?
• What should be done before climbing on and performing maintenance on an aircraft?
• Which orientation is recommended for safetying a clevis pin, when feasible?
• Which Army Regulation covers the management of SOF messages when combined with related manuals?
• Which WP in TM 1-1500-204-23 covers Eddy Current Testing?
• A straight (concentric) extension, like the one displayed, can be used on a torque wrench and requires no change in torque value applied.
• The guidance states that mixing MIL-PRF oils should be avoided.
• What defines a category one product quality deficiency?
• According to general maintenance manuals, fire extinguisher cylinders have a service life of:
• Paragraph 11 in safety messages is designated for Technical Procedures/Instructions.
• MIL-PRF-23699 and MIL-PRF-7808 oils are compatible oils and may be mixed and are interchangeable, but mixing should be avoided.
• DA Form 2408-15 is the?
• Which of the following describes ballast types as listed in maintenance material?
• How do you properly dispose of POL?
• Using a longer lever on a torque wrench will cause the wrench reading to be lower than the actual bolt torque for a fixed target torque.
• Which DA Form number corresponds to the Aircraft Inventory Record?
• If the torque wrench is set to 46.7 in-lbs with 8-inch length and 2-inch reverse extension, what is the resulting torque at the fastener (TA)?
• An ohmmeter can be connected to a live circuit.
• Which instrument would you use to verify a corner radius on a machined part?
• On a Torque Wrench Identification label, the marking CW stands for what?
• Lockwire of what minimum diameter shall be installed in holes greater than 0.045 inch?
• Which statement describes a Series circuit?
• TBO stands for what in maintenance terminology?
• What is the formula for extending lever length to achieve the specified torque?
• Which component is connected to the pitot-static system?
• Which statement best describes reverse extension?
• What are accumulators primarily used for in hydraulic systems?
• What is the purpose of the DA Form 2408-15 in aircraft maintenance records?
• What component provides air data derived from the pitot-static system?
• The Aviation Nondestructive Testing Program is described in which chapter?
• Feder Specification WW-T-700/1 pertains to which material?
• Suspended Tag Material uses which form number?
• MIL-H-5606 is which type of fluid?
• What does AGSE stand for?
• Who can authorize a one-time evacuation flight when the benefits outweigh the risk?
• Which statement about hydraulic fluid types is correct?
• What is NDI?
• Each company should appoint how many AMTP managers?
• What goes in the Contract or Purchase Order No. block on DD Form 1574 if the contract or PO number cannot be located?
• A Controlled Exchange is authorized when the required part cannot be obtained in time to meet operational readiness requirements.
• With a wrench length of 12 inches and a 2-inch reverse-extension adapter, what is the required TW to reach TA of 35 in-lbs?
• Which condition grounds the aircraft completely?
• Which item would be classified as Class II supply?
• Using a straight extension on a torque wrench requires a change in torque value applied.
• DA Form 2408-18 is the what?
• Which code is used to designate Desert Maintenance in TM 1-1500-204-23?
• Soldiers promoted into new units, transferred into the Army Reserve or National Guard, or inter-state transfer will be assessed for what?
• Which form is used to document equipment inspection results in aviation maintenance?
• Which statement correctly describes Circle X and Ground X?
• This is a picture of what kind of circuit?
• Functional group code 06 corresponds to which aircraft system?
• What is the status symbol for blade de-ice system fails self test, aircraft restricted from flight in known icing conditions?
• What WP in TM 1-500-204-23 covers rivets?
• What are some of the methods used to mutilate condemned items?
• Suspended Tag Materiel uses which form number?
• 46.7 in-lbs reading is equivalent to how many ft-lbs?
• What types of hydraulic fluids are currently authorized for use in Army aircraft?
• Suspended Tag Material is documented on which form?
• Which status symbol is appropriate for an inoperable landing light and aircraft restricted from night operations?
• Which regulation is cited as covering definitions and procedures for SOF messages in the context of maintenance documentation?
• ARMS surveys are conducted at what interval?
• What is the purpose of DA Form 2408-13-2?
• Servicing tires with the high pressure side of a nitrogen cart is authorized as long as the appropriate PPE is worn.
• The PMI-1 (480hr) on a H-60L is __ in working days.
• Which GEN AMAM superseded and replaced DA PAM 738-751?
• Which form is used for condemning unserviceable components?
• You need to torque a nut to 35 in-lbs using an 8-inch torque wrench with a 2-inch reverse-extension adapter. What should the torque wrench indicate (TW) on the handle to achieve the target torque (TA)?
• Lockwire diameter is specified for holes larger than which threshold?
• Which statement about the X symbol is true in maintenance status?
• Which of the following best describes the inclusion of UAS in AMAM scope?
• How many Theater Aviation Maintenance Sustainment Groups (TASMGs) are in the U.S. Army?
• Which of these are QC Section functions?
• When should brass cotter pins be used?
• What do Limited Test Flights evaluate?
• What is the purpose of DA Form 2407 in maintenance documentation?
• Which chapter covers the Aviation Nondestructive Testing Program in ADDENDUM 1 GEN-24-AMAM-01?
• A Class C fire extinguisher is used for which type of fires?
• What is the main difference between AN fittings and MS fittings?
• AMAM scope includes maintenance of which systems?
• A radius gauge is used for what purpose?
• What is the WP code for parking of aircraft and equipment in hangars?
• MOC stands for Maintenance Operation Check.
• The DA form 2410 has how many sections?
• What is the minimum breakaway torque for used all-metallic and nonmetallic self-locking nuts sized 3/4-16, fine threaded?
• Which condition imposes restrictions during flight?
• Which publication contains Aeronautical Equipment Maintenance Management Procedures?
• In hydraulic systems, accumulators primarily function as cushions against pressure surges.
• The status symbol that indicates a fault or condition that makes the aircraft inop or unsafe to fly is which letter?
• TM 1-1500-344-23 series relates to Cleaning and Corrosion Control. Which statement is true?
• Which symbol indicates grounding of the aircraft completely?
• When is a Controlled Exchange authorized?
• The EM number 0495 is tied to which document?
• Which statement is correct regarding MIL-H-5606?
• A 15B cannot cross train as a 15N.
• What does the DA Form 2408-15 document?
• DD Form 2332 is used for what?
• Pitot static system heaters are provided to prevent icing.
• How many types of lockpins are there?
• A tap is used for cutting which type of threads?
• DA Form 2408 is used for which purpose?
• Distortion is caused by
• A clevis pin should be safetied using which hardware, installed with the head up when possible?
• What solder should be used for tin-coated copper wire?
• If the target torque TA is doubled to 70 in-lbs with L = 8 inches and E = 2 inches reverse extension, what TW is required?
• Which publication number addresses aircraft cleaning and corrosion control?
• There are two types of self-retaining bolts. What are they?
• This AMAM has three adendums that supercedes (replace) DA Pam 738-751, TM 1-1500-328-23, and TB 43-0003-2
• What is the difference between Ground X condition and Circle X in aircraft maintenance statuses?
• What is the WP for parking of aircraft and equipment in hangars?
• What can be used to clean mercury?
• What instrument should be used to make logbook and maintenance form entries?
• Which color combination identifies hydraulic pressure lines on symbol identification tape?
• What ML level can directly supervise a ML0 per TC 3-04.71?
• A blue-yellow-blue printed symbol identification tape on an aluminum line indicates
• How are steel alloys produced?
• Relays are used for?
• Which manual covers the Army Safety Program?
• What are the levels of maintenance?
• Relays are used for
• Which equation correctly expresses the relationship for reverse extension between TA, TW, L, and E?
• Which symbol indicates a restriction during flight?
• Which form designation is used to document a maintainer's training record?
• Class II supply includes which items?
• The document TM 1-1500-328-23 (GEN-24-AMAM-01 ADDENDUM 3 version) covers which topic?
• DD Form 2332 is used for which purpose?
• Which statement about Title 32 technicians documenting AMTP training is correct?
• What does TASMG stand for?
• Which of the following is NOT a QC Section function?
• Which form is used to document a maintainer's training record?
• Which publication covers cleaning and corrosion control for aircraft?
• How many status symbols are there?
• Which form number is the aircraft inspection and maintenance record?
• Which aircraft have to be grounded if they are parked outside?
• What can be used to clean mercury?
• If no adapter is used (E equals 0) with an 8-inch wrench and a target torque of 35 in-lbs, what should the wrench be set to?
• DA Form 2407 is used for what purpose?